ROCHESTER (585) 292.9870 | ITHACA (607) 347.4455| DANSVILLE (585) 335.5970

Customer Service

You Can Build On

Contact Us?

News & Expert Advice

You are here: Home Tag ‘Dansville NY’

DECO LIQUID RELEASE – SpecChem | The Duke Company

The Duke Company is proud to carry SpecChem products including Cure Shield. DECO LIQUID RELEASE is a liquid release for decorative texturing mats. DECO LIQUID RELEASE is a colorless liquid release formulated and recommended for use with decorative,
mat-type concrete, texturing mats. It forms a lubricating barrier that prolongs the life of the imprinting tools by decreasing the friction between the mats and the concrete.

 

The Duke Company can assist you with all your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery. For exceptional customer service & the fastest delivery in Upstate New York, call us for a prompt rental quote.

Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)

 

 

 


DECO LIQUID RELEASE is used in the texturing process of both colored and uncolored concrete. It is also used as an alternative to powdered release agents that may not be desired in certain circumstances, such as interior projects.

 

APPLICATION

Trowel and finish newly poured concrete surfaces in preparation for the imprinting process. When the concrete has reached the plastic stage desirable for imprinting, DECO LIQUID RELEASE should be used between the texture mats and the concrete to prevent sticking and concrete build up.

Apply in temperatures between 55 degree F and 80o degrees F. Using a pump-type sprayer, liberally apply a mist of DECO LIQUID
RELEASE on the texturing mats AND on the concrete surface, but only on the area where you are going to place the next few mats. Apply over an area of approximately 10 to 15 square feet to avoid evaporation before the mat placements are made, especially on dry windy
days.

COVERAGE
One gallon of DECO LIQUID RELEASE will release approximately 150-250 square feet of concrete surface.

 


Download Helpful Information:


Packaging

CURE HARD is packaged in:

  • 55 gallon drums (208.2 L)
  • 5 gallon pails (18 L)


The Duke Company
 can assist you with your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery.

         

Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)


The Duke Company ships nationwide and throughout New York, or contact us for convenient pick-up locations including:

Sign-up for the Duke Company’s Alerts

Text ‘DUKESALT’ to ’55469’ to receive text messages regarding our hours, extended hours, schedule changes and discount opportunities.

Industries we serve:

Construction

High Rises,
Bridges,
Residential & Commercial
high-rise construction, power plants,
tunnels,
mining
Building Maintenance

By David Szydlowski

CURESHIELD EX – SpecChem | The Duke Company

The Duke Company is proud to carry SpecChem products including Cure Shield. Cure Shield EX is a one step, low VOC Cure & Seal containing Silane. CURESHIELD EX is a solvent based blend of silane and pure acrylic copolymers designed to cure and seal fresh concrete. CURESHIELD EX is a unique solvent based blend of silane and pure acrylic copolymers designed to cure, seal, harden and dustproof fresh concrete and provide additional protection to existing concrete.

 

The Duke Company can assist you with all your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery. For exceptional customer service & the fastest delivery in Upstate New York, call us for a prompt rental quote.

Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)

 

 


In addition to forming an effective film forming curing and sealing compound, it also contains silane. Silane penetrates the fresh concrete and provides protection against spalling and deterioration of concrete structures caused by deicing salts.

CURESHIELD EX can be applied to fresh concrete unlike other siloxane, silane type products and also meets ASTM C-309 and 1315 curing standards.

CURESHIELD EX penetrates the surface and bonds directly with the substrate, which results in a surface that is highly resistant to moisture and salt.

 

APPLICATION

Coverage: Ready to use. Do not dilute. Apply with a sprayer in uniform thin film; spray apply for best results. Apply a single coat uniformly and do not allow to puddle. Apply in accordance with recommended coverage rates.

Curing Fresh Concrete: 200 – 250 sq ft / gal
Aged concrete: 200 – 300 sq ft / gal

On broom or rough finished concrete, increase the coverage rate to compensate for the added surface area. Coverage may vary due to porosity and conditions of the concrete.

New Concrete: CURESHIELD EX should be applied as soon as the surface water has disappeared and the concrete surface will not be marred by the walking applicator. At this point, apply in a uniform coat leaving no gaps. Do not allow the material to puddle.

Existing Concrete: Concrete surface must be clean, dry or damp and free of all stains, oil, grease, dirt, and other contaminants that can prevent adhesion or penetration of the CureShield EX An application of CURESHIELD EX will renovate existing concrete surfaces. These surfaces will be brighter and easier to clean and maintain.

NOTE: CureShield EX dries much faster than standard solvent –based product. CureShield EX should not be applied on hot surfaces or in direct sunlight as this could cause rapid evaporation and will not allow the film to form properly. Under these conditions the film may
bubble, peel and/or blush. Tip: If spraying CureShield EX keep pressure in pump up sprayers as high as possible to ensure a steady and even spray pattern. Maintain the sprayer tip near the concrete surface, within 12 inches.


Download Helpful Information:


Packaging

CURE HARD is packaged in:

  • 55 gallon drums (208.2 L)
  • 5 gallon pails (18 L)


The Duke Company
 can assist you with your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery.

         

Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)


The Duke Company ships nationwide and throughout New York, or contact us for convenient pick-up locations including:

Sign-up for the Duke Company’s Alerts

Text ‘DUKESALT’ to ’55469’ to receive text messages regarding our hours, extended hours, schedule changes and discount opportunities.

Industries we serve:

Construction

High Rises,
Bridges,
Residential & Commercial
high-rise construction, power plants,
tunnels,
mining
Building Maintenance

By David Szydlowski

CURESHIELD – SpecChem | The Duke Company

The Duke Company is proud to carry SpecChem products including Cure Shield. Cure Shield is a one-Step Cure & Seal containing Silan. CURESHIELD is a solvent based blend of silane and pure acrylic copolymers designed to cure and seal fresh concrete
and provide additional protection to existing concrete.

 

The Duke Company can assist you with all your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery. For exceptional customer service & the fastest delivery in Upstate New York, call us for a prompt rental quote.

Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)

 

 

 


CURESHIELD provides a non yellowing, clear film which effectively cures and protects fresh concrete. In addition to forming an effective film forming curing andsealing compound, it also contains silane. Silane penetrates the fresh concrete and provides protection against
spalling and deterioration of concrete structures caused  by deicing salts.  CURESHIELD can be applied to fresh concrete unlike other
siloxane, silane type products and also meets ASTM C-309 and 1315 curing standards. CURESHIELD penetrates the surface and bonds directly with the substrate, which results in a surface that is highly resistant to moisture and salt.

 

APPLICATION

Coverage: Ready to use. Do not dilute. Apply with a sprayer or roller in uniform thin film; spray apply for best results. Apply a single coat uniformly and do not allow to puddle. Apply in accordance with recommended coverage rates.

Curing Fresh Concrete: 200 – 250 sq ft / gal
Aged concrete: 200 – 300 sq ft / gal

On broom or rough finished concrete, increase the coverage rate to compensate for the added surface area. Coverage may vary due to porosity and conditions of the concrete.

New Concrete: CURESHIELD should be applied as soon as the surface water has disappeared and the concrete surface will not be marred by the walking applicator. At this point, apply in a uniform coat leaving no gaps. Do not allow the material to puddle.

Existing Concrete: Concrete surface must be clean, dry or damp and free of all stains, oil, grease, dirt, and other contaminants that can prevent adhesion or penetration of the CureShield.

An application of CURESHIELD will renovate existing concrete surfaces. These surfaces will be brighter and easier to clean and maintain.


Download Helpful Information:


Packaging

CURE HARD is packaged in:

  • 55 gallon drums (208.2 L)
  • 5 gallon pails (18 L)


The Duke Company
 can assist you with your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery.

         

Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)


The Duke Company ships nationwide and throughout New York, or contact us for convenient pick-up locations including:

Sign-up for the Duke Company’s Alerts

Text ‘DUKESALT’ to ’55469’ to receive text messages regarding our hours, extended hours, schedule changes and discount opportunities.

Industries we serve:

Construction

High Rises,
Bridges,
Residential & Commercial
high-rise construction, power plants,
tunnels,
mining
Building Maintenance

By David Szydlowski

CURE HARD – SpecChem | The Duke Company

The Duke Company is proud to carry SpecChem products including CURE HARD. CURE HARD is a Sodium silicate cure & dustproofer.

The Duke Company can assist you with all your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery. For exceptional customer service & the fastest delivery in Upstate New York, call us for a prompt rental quote.

Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)

 

 


CURE HARD is a spray applied concrete cure, hardener and dustproofer. CURE HARD deeply penetrates concrete surfaces to densify, seal, harden and dustproof concrete and Portland Cement based material surfaces to help them achieve maximum abrasion resistance and without altering the natural appearance of the concrete. May contribute to LEED credits.

  • Economical and ready to use
  • Does not alter natural color of aggregate or concrete
  • Non-flammable
  • Actual VOC = 0g/l, odorless
  • Helps seal concrete against acids, oils, greases, salts and tire marks
  • Will not inhibit the adhesion of secondary toppings

 

APPLICATION

COVERAGE

Curing, sealing, hardening and dustproofing:

  • Hard Troweled Finish: 300-500 sq ft / gal
  • Broom or Float Finish: 200-400 sq ft / gal
  • Rough Finish: 200-300 sq ft / gal
  • Aged Concrete: 200-300 sq ft / gal
  • Vertical Surface: 200-300 sq ft / gal

The above rates are approximate. Exact coverage depends upon the porosity of the concrete as well as the job requirements. For optimum hardening of porous surfaces, apply two coats.

Apply immediately after final finishing operations and after the bleed water had receded. Brush out puddles and runs. Over application and puddling will leave white crystals, which must be removed by immediately flushing the surface with water and scrubbing.

May be applied with sprayer, brush or roller. Spraying provides superior results.

Application temperatures 40 F to 100 F

Protect metal, glass, painted and brick surfaces from CURE HARD. If accidentally misapplied, wash with clean water at once.

For aged concrete, surface must be free of dirt and all other foreign matter. Surface should be dry to permit
maximum penetration.

As jobsite conditions vary, a test panel should always be
performed.


Download Helpful Information:


Packaging

CURE HARD is packaged in:

  • 55 gallon drums (208.2 L)
  • 5 gallon pails (18 L)


The Duke Company
 can assist you with your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery.

         

Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)


The Duke Company ships nationwide and throughout New York, or contact us for convenient pick-up locations including:

Sign-up for the Duke Company’s Alerts

Text ‘DUKESALT’ to ’55469’ to receive text messages regarding our hours, extended hours, schedule changes and discount opportunities.

Industries we serve:

Construction

High Rises,
Bridges,
Residential & Commercial
high-rise construction, power plants,
tunnels,
mining
Building Maintenance

By David Szydlowski

Cure & Seal 30 – SpecChem | The Duke Company

The Duke Company is proud to carry SpecChem products including Cure & Seal 30. Cure & Seal 30 is a 30% solids solvent-based cure & seal (ASTM 1315 class B compliant).

The Duke Company can assist you with all your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery. For exceptional customer service & the fastest delivery in Upstate New York, call us for a prompt rental quote.

              Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)

 

 

 


CURE & SEAL 30 is a VOC compliant acrylic polymer engineered to cure, seal, harden, and dustproof freshly placed concrete and improve the wearability and durability of aged concrete surfaces.

 

APPLICATION

Storage: Store material in the original tightly closed containers. Do not allow the accumulation of water, dirt or other contaminants.

Coverage: Ready to use. Do not dilute. Apply with a sprayer or roller in uniform thin films; spray apply for best results. Two thin coats should be applied. Apply the second coat after the first coat has thoroughly dried. Never apply one heavy coat. Avoid puddles. Apply in accordance with recommended coverage rates.

Curing: 300 – 400 sq ft / gal
Dustproofing and Sealing: 400 – 600 sq ft / gal
Aged concrete: 400 – 600 sq ft / gal

For dustproofing and sealing benefits, apply two coats at 500 sq ft / gal. On broom or rough finished concrete, double the coverage rate. Coverage may vary due to porosity and conditions of the concrete.

New Concrete: CURE & SEAL 30 should be applied as soon as the surface water has disappeared and the concrete surface will not be marred by the walking applicator. At this point, apply in a uniform coat. For a superior finish and added curing and sealing protection, apply a second coat at 400 sq ft / gal.

Existing Concrete: Concrete surface must be clean, dry or damp and free of all stains, oil, grease, dirt, and incompatible coatings prior to application. An application of CURE & SEAL 30 will renovate existing concrete, brick or terrazzo floors. These surfaces will be brighter and easier to clean and maintain. CURE & SEAL 30 is compatible with most carpets, tile and floor covering adhesives. Due to the wide variation in the chemistry of adhesives, a test section is always recommended.


Download Helpful Information:


Packaging

CURE & SEAL 30 is packaged in:

  • 55 gallon drums (208.2 L)
  • 5 gallon pails (18 L)


The Duke Company
 can assist you with your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery.

         

              Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)


The Duke Company ships nationwide and throughout New York, or contact us for convenient pick-up locations including:

Sign-up for the Duke Company’s Alerts

Text ‘DUKESALT’ to ’55469’ to receive text messages regarding our hours, extended hours, schedule changes and discount opportunities.

Industries we serve:

Construction

High Rises,
Bridges,
Residential & Commercial
high-rise construction, power plants,
tunnels,
mining
Building Maintenance

By David Szydlowski

CURE & SEAL 25 UV EX-SpecChem | The Duke Company

The Duke Company is proud to carry SpecChem products including CURE & SEAL 25 UV EX. CURE & SEAL 25 UV EX is a 25% solids, low VOC, solvent-based cure & seal (ASTM C-1315 Class A)

 

The Duke Company can assist you with all your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery. For exceptional customer service & the fastest delivery in Upstate New York, call us for a prompt rental quote.

              Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)

 


CURE & SEAL 25 UV EX is a VOC compliant nonyellowing, acrylic polymer engineered to cure, seal, harden, and dustproof freshly placed concrete and improve the wearability and durability of aged concrete surfaces. CURE & SEAL 25 UV EX is formulated with a unique solvent blend allowing fast-drying, solvent-base performance along with VOC compliance in the OTC/LADCO/ MRPO regions.

APPLICATION

Cure & Seal 25 UV EX dries much faster than standard solvent-based products. Cure & Seal 25 UV EX should not be applied on hot surfaces or in direct sunlight as this could cause rapid evaporation and will not allow the film to form properly. Under these conditions the film may bubble, peel and/or blush. Tip: If spraying Cure & Seal 25 UV EX keep pressure in pump up sprayers as high as possible to ensure a steady and even spray pattern. Maintain the prayer tip near the concrete, within 12 inches.

Curing: 300 – 400 sq ft / gal
Dustproofing and Sealing: 400 – 600 sq ft / gal
Aged concrete: 400 – 600 sq ft / gal

For dustproofing and sealing benefits, apply two coats at 500 sq ft / gal. On broom or rough finished concrete, double the coverage rate. Coverage may vary due to porosity and conditions of the concrete.

New Concrete: CURE & SEAL 25 UV EX should be applied as soon as the surface water has disappeared and the concrete surface will not be marred by the walking applicator. At this point, apply in a uniform coat. For a superior finish and added curing and sealing protection, apply a second coat at 400 sq ft / gal.

Existing Concrete: Concrete surface must be clean, dry or damp and free of all stains, oil, grease, dirt, and incompatible coatings prior to application. An application of CURE & SEAL 25 UV EX will renovate existing concrete, brick or terrazzo floors. These surfaces will be brighter and easier to clean and maintain.

CURE & SEAL 25 UV EX is compatible with most carpets, tile and floor covering adhesives. Due to the wide variation in the chemistry of adhesives, a test section is always recommended.


Download Helpful Information:


Packaging

CURE & SEAL 25 UV EX is packaged in:

  • 55 gallon drums (208.2 L)
  • 5 gallon pails (18 L)


The Duke Company
 can assist you with your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery.

         

              Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)


The Duke Company ships nationwide and throughout New York, or contact us for convenient pick-up locations including:

Sign-up for the Duke Company’s Alerts

Text ‘DUKESALT’ to ’55469’ to receive text messages regarding our hours, extended hours, schedule changes and discount opportunities.

Industries we serve:

Construction

High Rises,
Bridges,
Residential & Commercial
high-rise construction, power plants,
tunnels,
mining
Building Maintenance

By David Szydlowski

CURE & SEAL 25 UV-SpecChem | The Duke Company

 

The Duke Company is proud to carry SpecChem products including CURE & SEAL 25 UV. CURE & SEAL 25 UV is a 25% solids, low VOC, solvent-based cure & seal.

CURE & SEAL 25 UV is a 25% solids solvent-based cure & seal (ASTM C-1315 Class A compliant).

The Duke Company can assist you with all your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery. For exceptional customer service & the fastest delivery in Upstate New York, call us for a prompt rental quote.

              Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)

 


CURE & SEAL 25 UV is a VOC compliant acrylic nonyellowing polymer engineered to cure, seal, harden, and dustproof freshly placed concrete and improve the wearability and durability of aged concrete surfaces. CURE & SEAL 25 UV is formulated to provide maximum color stability in a high gloss finish. CURE & SEAL 25 UV is stable under Ultra-Violet light and is suitable for both exterior and interior use.

APPLICATION

Storage: Store material in the original tightly closed containers. Do not allow the accumulation of water, dirt or other contaminants.

Coverage: Ready to use. Do not dilute. Apply with a sprayer or roller in uniform thin films; spray apply for best results. Two thin coats should be applied. Apply the second coat after the first coat has thoroughly dried. Never apply one heavy coat. Avoid puddles. Apply in accordance with recommended coverage rates.

Curing: 300 – 400 sq ft / gal
Dustproofing and Sealing: 400 – 600 sq ft / gal
Aged concrete: 400 – 600 sq ft / gal

For dustproofing and sealing benefits, apply two coats at 500 sq ft / gal. On broom or rough finished concrete, double the coverage rate. Coverage may vary due to porosity and conditions of the concrete.

New Concrete: CURE & SEAL 25 UV should be applied as soon as the surface water has disappeared and the concrete surface will not be marred by the walking applicator. At this point, apply in a uniform coat. For a superior finish and added curing and sealing protection, apply a second coat at 400 sq ft / gal.

Existing Concrete: Concrete surface must be clean, dry or damp and free of all stains, oil, grease, dirt, and incompatible coatings prior to application. An application of CURE & SEAL 25 UV will renovate existing concrete, brick or terrazzo floors. These surfaces will be brighter and easier to clean and maintain.


Download Helpful Information:


Packaging

CURE & SEAL 25 UV is packaged in:

  • 55 gallon drums (208.2 L)
  • 5 gallon pails (18 L)


The Duke Company
 can assist you with your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery.

         

              Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)


The Duke Company ships nationwide and throughout New York, or contact us for convenient pick-up locations including:

Sign-up for the Duke Company’s Alerts

Text ‘DUKESALT’ to ’55469’ to receive text messages regarding our hours, extended hours, schedule changes and discount opportunities.

Industries we serve:

Construction

High Rises,
Bridges,
Residential & Commercial
high-rise construction, power plants,
tunnels,
mining
Building Maintenance

By David Szydlowski

SpecChem CURE & SEAL 25 EX | The Duke Company

The Duke Company is proud to carry SpecChem products including CURE & SEAL 25 EX. CURE & SEAL 25 EX is a 25% solids, low VOC, solvent-based cure & seal.

CURE & SEAL 25 EX is a VOC compliant acrylic polymer engineered to cure, seal, harden, and dustproof freshly placed concrete and improve the wearability and durability of aged concrete surfaces.

The Duke Company can assist you with all your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery. For exceptional customer service & the fastest delivery in Upstate New York, call us for a prompt rental quote.

 

              Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)

 


CURE & SEAL 25 EX is formulated with a unique solvent blend allowing fast-drying, solvent-base performance along with VOC compliance in the OTC/LADCO/MRPO regions.

 

APPLICATION

Cure & Seal 25 EX dries much faster than standard solvent-based products. Cure & Seal 25 EX should not be applied on hot surfaces or in direct sunlight as this could cause rapid evaporation and will not allow the film to form properly. Under these conditions the film may bubble, peel and/or blush. Tip: If spraying Cure & Seal 25 EX keep pressure in pump up sprayers as high as possible to ensure a steady and even spray pattern. Maintain the sprayer tip near the concrete, within 12 inches.

Curing: 300 – 400 sq ft / gal
Dustproofing and Sealing: 400 – 600 sq ft / gal
Aged concrete: 400 – 600 sq ft / gal

For dustproofing and sealing benefits, apply two coats at 500 sq ft / gal. On broom or rough finished concrete, double the coverage rate. Coverage may vary due to porosity and conditions of the concrete.

New Concrete: CURE & SEAL 25 EX should be applied as soon as the surface water has disappeared and the concrete surface will not be marred by the walking applicator. At this point, apply in a uniform coat. For a superior finish and added curing and sealing protection, apply a second coat at 400 sq ft / gal.

Existing Concrete: Concrete surface must be clean, dry or damp and free of all stains, oil, grease, dirt, and incompatible coatings prior to application. An application of CURE & SEAL 25 EX will renovate existing concrete, brick or terrazzo floors. These surfaces will be brighter and easier to clean and maintain.

CURE & SEAL 25 EX is compatible with most carpets, tile and floor covering adhesives. Due to the wide variation in the chemistry of adhesives, a test section is always recommended.


Download Helpful Information:


Packaging

CURE & SEAL 25 EX is packaged in:

  • 55 gallon drums (208.2 L)
  • 5 gallon pails (18 L)


The Duke Company
 can assist you with your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery.

         

              Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)


The Duke Company ships nationwide and throughout New York, or contact us for convenient pick-up locations including:

Sign-up for the Duke Company’s Alerts

Text ‘DUKESALT’ to ’55469’ to receive text messages regarding our hours, extended hours, schedule changes and discount opportunities.

Industries we serve:

Construction

High Rises,
Bridges,
Residential & Commercial
high-rise construction, power plants,
tunnels,
mining
Building Maintenance

By David Szydlowski

SpecChem CURE & SEAL 25 | The Duke Company

The Duke Company is proud to carry SpecChem products including CURE & SEAL 25. CURE & SEAL 25 is a 25% solids solvent-based cure & seal.

CURE & SEAL 25 is a VOC compliant acrylic polymer engineered to cure, seal, harden, and dustproof freshly placed concrete and improve the wearability and durability of aged concrete surfaces.

The Duke Company can assist you with all your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery. For exceptional customer service & the fastest delivery in Upstate New York, call us for a prompt rental quote.

              Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)

 

 

 

 


CURE & SEAL 25 is a 25% solids solvent-based cure & seal.

 

APPLICATION

Coverage: Ready to use. Do not dilute. Apply with a sprayer or roller in uniform thin films; spray apply for best results. Two thin coats should be applied. Apply the second coat after the first coat has thoroughly dried. Never apply one heavy coat. Avoid puddles. Apply in accordance with recommended coverage rates.

Curing: 300 – 400 sq ft / gal
Dustproofing and Sealing: 400 – 600 sq ft / gal
Aged concrete: 400 – 600 sq ft / gal

For dustproofing and sealing benefits, apply two coats at 500 sq ft / gal. On broom or rough finished concrete, double the coverage rate. Coverage may vary due to porosity and conditions of the concrete.

New Concrete: CURE & SEAL 25 should be applied as soon as the surface water has disappeared and the concrete surface will not be marred by the walking applicator. At this point, apply in a uniform coat. For a superior finish and added curing and sealing protection, apply a second coat at 400 sq ft / gal.

CURE & SEAL 25 should be applied as soon as the surface water has disappeared and the concrete surface will not be marred by the walking applicator. At this point, apply in a uniform coat. For a superior finish and added curing and sealing protection, apply a second coat at 400 sq ft / gal.

CURE & SEAL 25 is compatible with most carpets, tile and floor covering adhesives. Due to the wide variation in the chemistry of adhesives, a test section is always recommended.

 

SHELF LIFE

Shelf life of CURE & SEAL 25 in the original tightly closed containers is two years from the date of manufacture. Do not allow the accumulation of water, dirt, or other contaminants.


Download Helpful Information:


Packaging

CURE & SEAL 25 is packaged in:

  • 55 gallon drums (208.2 L)
  • 5 gallon pails (18 L)


The Duke Company
 can assist you with your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery.

         

              Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)


The Duke Company ships nationwide and throughout New York, or contact us for convenient pick-up locations including:

Sign-up for the Duke Company’s Alerts

Text ‘DUKESALT’ to ’55469’ to receive text messages regarding our hours, extended hours, schedule changes and discount opportunities.

Industries we serve:

Construction

High Rises,
Bridges,
Residential & Commercial
high-rise construction, power plants,
tunnels,
mining
Building Maintenance

By David Szydlowski

SpecChem – CRYSTAL SHINE Matte | The Duke Company

The Duke Company is proud to carry SpecChem products including Crystal Shine MatteCrystal Shine Matte is a Matte Finish Protective Exterior Sealer.

CRYSTAL SHINE MATTE is a methacrylate cure and sealer developed specifically exterior applications, including exposed aggregate and other decorative concrete surfaces. CRYSTAL SHINE MATTE provides a clear protective coating that produces a subtle, satin (“matte”) finish that highlights the color and texture of surfaces without excessive shine. CRYSTAL SHINE MATTE is ideal for stained concrete, exposed aggregate slabs, walkways, swimming pool decks and walls.

The Duke Company can assist you with all your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery. For exceptional customer service & the fastest delivery in Upstate New York, call us for a prompt rental quote.

              Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)

 

 

SpecChem logo

 


CRYSTAL SHINE MATTE is ideal for stained concrete, exposed aggregate slabs, walkways, swimming pool decks and walls.

BENEFITS:

  • Provides a totally clear membrane for new or old concrete for improved durability.
  • Seals all concrete surfaces, providing a satin (“matte”) appearance and easier clean-up.
  • Dust proofs concrete with a tough, durable film.
  • Will not yellow under ultraviolet exposure.
  • Excellent blush resistance in damp areas.

 

 

APPLICATION

Surface Preparation – The concrete surface must be clean and free of standing water. Remove any sealer or other material that may prevent adhesion of CRYSTAL SHINE MATTE.AGITATE WELL BEFORE EVERY USE!

Application to Fresh Concrete – Apply at a uniform coverage by spray or roller at 350-400 sq ft /gal. Product may be sprayed with a hand held “pump-up” sprayer or an airless industrial sprayer. If roller applied, use a short napped solvent resistant sleeve. When an extra high gloss is desired or on especially porous surfaces, another thin application can be applied the next day at 400 sq-ft/gal.

Sealing Existing Concrete – The surface must be thoroughly cleaned and dried before applying Crystal Shine Matte. Pressure washing with a strong alkaline detergent to remove dirt, waxes and oils is recommended. Acids will not sufficiently clean or remove dirt, curing compounds, or old sealer from concrete. Worn or porous areas may need a second application for uniform sealing and appearance. Allow 24 hours before 2nd application of sealer. In general, multiple thin coats (350 – 400 sq ft/ gal) will provide a harder, more durable finish than a single heavy application. Dry time will be influenced by both temperature and humidity.

 


Download Helpful Information:


Packaging

Crystal Shine Matte is packaged in:

  • 55 gallon drums (208.2 L)
  • 5 gallon pails (18 L)
  • 1 gallon cans (4 to a case) (3.8 L)


The Duke Company
 can assist you with your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery.

         

              Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)


The Duke Company ships nationwide and throughout New York, or contact us for convenient pick-up locations including:

Sign-up for the Duke Company’s Alerts

Text ‘DUKESALT’ to ’55469’ to receive text messages regarding our hours, extended hours, schedule changes and discount opportunities.

Industries we serve:

Construction

High Rises,
Bridges,
Residential & Commercial
high-rise construction, power plants,
tunnels,
mining
Building Maintenance

By David Szydlowski

Contact Us

Get Help Now

Our Team Is Standing By

Building & Ice Control Products

Buy Used Equipment

Used Equipment

A comprehensive line of Used Equipment is available for purchase. Our Used Equipment specialists would be glad to assist you.

A+ Reputation

Great Work Ethic!

"Didn't know the Duke Co. before, but now I do. Great employee." - Prospective Customer from Lancaster

Thank You!!

"Duke provides the products, service, knowledge, and logistics that keep our company competitive! Thank you and don't change a thing!" - Brian K.

Leave A Review
See All Testimonials

Parts & Service Questions?

Parts & Service

We can service your equipment and order parts for you. Our Parts & Service professionals are available to assist you.

Training & Advice

DECO LIQUID RELEASE – SpecChem | The Duke Company

The Duke Company is proud to carry SpecChem products including Cure Shield. DECO LIQUID RELEASE is a liquid release for decorative texturing mats. DECO LIQUID RELEASE is a colorless liquid release formulated and recommended […]

Read More...

CURESHIELD EX – SpecChem | The Duke Company

The Duke Company is proud to carry SpecChem products including Cure Shield. Cure Shield EX is a one step, low VOC Cure & Seal containing Silane. CURESHIELD EX is a solvent based blend of silane and […]

Read More...

Read All

Recent Videos

Video – How to Start a Handheld Hydraulic Hammer

Video – How to Start a Handheld Hydraulic Hammer

Are you looking for a helpful video on how to start a handheld hydraulic hammer?   This excellent […]

Duke Company Rock Salt Distribution in Upstate NY, NYC and New York State

Video Highlights – Duke Company Rock Salt Distribution in Upstate NY, NYC and New York State

The Duke Company can help keep you warm and your property clear, safe and accessible this Winter. This […]

View All

Buy Used Equipment NOW