ROCHESTER (585) 292.9870 | ITHACA (607) 347.4455| DANSVILLE (585) 335.5970

Customer Service

You Can Build On

Contact Us?

News & Expert Advice

You are here: Home Tag ‘SC Foundation Coating’

The Duke Company | SC Foundation Coating

 

 

The Duke Company is proud to carry SpecChem products including SC Foundation Coating. SC Foundation Coating is a polymer modified, cement based waterproofing coating formulated to provide superior water-resistant concrete and masonry substrates.
SC Foundation Coating is designed to waterproof the exterior surface of below grade concrete and masonry. SC FOUNDATION COATING closes the internal voids in the substrate, but still allows full breathablilty.

 

Benefits:

  • Waterproofs interior, exterior, above & below grade masonry & concrete surfaces.
  • Apply to concrete block, brick, stone, precast concrete or formed concrete.
  • Apply to both positive & negative side (when hydrostatic pressure is low & aesthetics are not important.

 

 


 

The Duke Company can assist you with all your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery. For exceptional customer service & the fastest delivery in Upstate New York, call us for a prompt rental quote.

 

Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)

 

 

 


 

Application

Surface Preparation: The surface must be structurally sound, clean, and free of dirt, release agents, efflorescence, curing compounds, laitance, and other contaminates. Remove form marks and other protrusions to prevent “show through”. Form a cove at the footer-wall intersection point and fill all broken corners of block and breaks in the surface. Repair all surface defects including cracks and voids with SC FOUNDATION COATING mixed to a mortar consistency. Cut back wires a minimum of 3/4” and repair with Spec Patch or Spec Plug.
Dampen the surface with clean water immediately before SC FOUNDATION COATING application.

Mixing: SC FOUNDATION COATING must be mechanically mixed using a slow speed motor and mixing blade to thoroughly disperse the ingredients. Mix for approximately three minutes. Do not over-mix the material.  Pour approximately one half of the required two gallons
into an empty, clean container and begin slow speed mixing. Slowly add SC FOUNDATION COATING and mixing admixture* (water or Acrylic Bonder) as needed to bring the mixture to a heavy, completely blended pancake batter consistency. Stop mixing and allow the mixture to ‘fatten” for ten minutes. Re-mix and, if necessary, add more mixing admixture to reduce batter consistency. *Note: To improve bonding & mechanical properties on concrete, masonry and for all trowel applications, prepare an acrylic admixture using 1 part Acrylic bonder and 3 parts potable water. For example two gallons of mixing admixture consists of two quarts of Acrylic Bonder blended
with six quarts of water. When using as a pointing mortar, the use of Acrylic Bonder admixture is recommended.

Application: Pre-dampen the substrate with clean, potable water before any application. All applications should carry down to and over the footer, forming a cove at the walls-footer intersection. Apply two uniform applications of SC Foundation Coating, each application at approximately 1- 2 lbs/yd2, allowing 24 hours between applications. Make sure both applications carry down to and over the footer, forming a 1-1/2” (38cm) cove at the junction of walls and footers  Hand Brush: Apply using a six inch cement masons brush. Load bristles and lay on a heavy coat using long, smooth horizontal strokes. Apply sufficient material to fill voids. Final strokes should all be
in one direction to produce an even texture and finish. Allow first coat to dry for 12 to 24 hours before applying a finish coat.

Push Broom: Use a five gallon pail or wide mount tub to hold product. Dip a ten inch, Tampico bristle push broom into product mix just enough to load the bristles. Apply a heavy coat using long, even horizontal strokes. Apply sufficient material to fill all voids. Lift the brush at the end of each stroke. Final strokes should all be in one direction to produce and even texture & finish. Do not over-brush. Allow the first
coat to dry for 12 to 24 hours before applying a finish coat. Spray: Use heavy duty spray equipment capable of spraying cement-based products or mastics. Trowel: The use of trowel applications is required in some severe water pressure situations.

 

 


Download Helpful Information:


 



The Duke Company
 can assist you with your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery.

         

Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)


The Duke Company ships nationwide and throughout New York, or contact us for convenient pick-up locations including:

Sign-up for the Duke Company’s Alerts

Text ‘DUKESALT’ to ’55469’ to receive text messages regarding our hours, extended hours, schedule changes and discount opportunities.

Industries we serve:

Construction

High Rises,
Bridges,
Residential & Commercial
high-rise construction, power plants,
tunnels,
mining
Building Maintenance

By David Szydlowski

 

Contact Us

Get Help Now

Our Team Is Standing By

Building & Ice Control Products

Buy Used Equipment

Used Equipment

A comprehensive line of Used Equipment is available for purchase. Our Used Equipment specialists would be glad to assist you.

A+ Reputation

Great Work Ethic!

"Didn't know the Duke Co. before, but now I do. Great employee." - Prospective Customer from Lancaster

Thank You!!

"Duke provides the products, service, knowledge, and logistics that keep our company competitive! Thank you and don't change a thing!" - Brian K.

Leave A Review
See All Testimonials

Parts & Service Questions?

Parts & Service

We can service your equipment and order parts for you. Our Parts & Service professionals are available to assist you.

Training & Advice

Viper® VaporCheck | Duke Company

The Duke Company is proud to carry Insulation Solutions products. For example, Viper® VaporCheck. Viper® VaporCheck® is designed to help builders control vapor and moisture infiltration in homes and buildings. The cross-woven polyethylene […]

Read More...

Viper® VaporCheck® II | Duke Company

Viper® VaporCheck® II     Viper® VaporCheck® II is a multi-layer, extruded, HD virgin polyolefin under slab vapor barrier / retarder. The “virgin resin” used when manufacturing Viper VaporCheck II prevents material breakdown when exposed […]

Read More...

Read All

Recent Videos

Video – How to Start a Handheld Hydraulic Hammer

Video – How to Start a Handheld Hydraulic Hammer

Are you looking for a helpful video on how to start a handheld hydraulic hammer?   This excellent […]

Duke Company Rock Salt Distribution in Upstate NY, NYC and New York State

Video Highlights – Duke Company Rock Salt Distribution in Upstate NY, NYC and New York State

The Duke Company can help keep you warm and your property clear, safe and accessible this Winter. This […]

View All

Buy Used Equipment NOW