The Duke Company is proud to carry SpecChem products including RepCon® 928. RepCon® 928 is a Single component polymer-modified rapid setting concrete repair mortar.

RepCon® 928 is a single component, polymer modified, fiber reinforced, rapid setting concrete repair mortar with corrosion inhibitor for use on concrete floors, highway pavements, bridge decks and other applications requiring early resumption of traffic or use. RepCon® 928 is formulated to meet the requirements of ASTM C928 Packaged, Dry, Rapid Hardening Cementitious Material for Concrete
Repair and AASHTO T260. RepCon® 928 incorporates the latest in polymer technology offering superior durability, performance and ease of application without liquid activators for horizontal and vertical form & pour applications

BENEFITS:

  • One component, dry-polymer modified. Just add water.
  • Fiber-reinforced for added flexural strength
  • Air entrained for excellent freeze-thaw durability
  • Natural concrete-gray color
  • Suitable for horizontal and formed vertical application
  • Takes foot traffic in 1 hour after set
  • Long work time for hot weather applications (available in fast-set version RepCon® 928 FS)

 

The Duke Company can assist you with all your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery. For exceptional customer service & the fastest delivery in Upstate New York, call us for a prompt rental quote.

 

Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)

 

 

 

 


 

Application

Surface Preparation: The concrete must be sound and free of all foreign material, including oil, grease, dust, laitance or other surface contaminants. For maximum durability, saw cut the perimeter of the repair 1/8” deeper than the depth of the repair, creating a notched, reinforced edge. Mechanically abrade the surface by an engineered approved method in accordance with ICRI 310.2 Guideline to a minimum CSP 5. All concrete surfaces to be repaired must be in a saturated-surface-damp (SSD) condition with no standing water on the surface.

Priming/Scrub Coat: Thoroughly clean all exposed steel reinforcing of rust and coat with SpecPrep SB.
Prepared concrete must be SSD and primed with a spray or brush coat of SpecPrep SB and the repair mortar applied wet on wet or up to the recommended open time (see SpecPrep SB technical data sheet).
As an alternative, apply a scrub coat of the properly mixed repair mortar by scrubbing a thin layer into the predampened substrate with a stiff brush. Place the repair mortar immediately before the bond coat dries.

Mix 4.75 – 5.25 pints (depending on desired consistency) of clean water per 50 pound bag of material.
Mix with a low speed drill or mortar mixer. Add recommended amount of clean water into the container, followed by slowly adding the RepCon® 928 powder. Mix 2-3 minutes. Mix only what can be applied within the setting period. Depending on the area dimensions, RepCon® 928 can be applied in applications from 1” to 6” in a lift without extension.

Deep Applications: For repair applications over 2”, RepCon® 928 can be extended with clean, SSD, 3/8” aggregate up to 60% by weight (30lbs) and mixed an additional 2 min. Choose a clean (free of organic material) wellgraded 3/8” aggregate. Aggregate should be predampened prior to mixing with RepCon® 928. The total mixing water for the batch shall be reduced by the amount of free water found in the aggregate. This extension will add approx 0.18 cu-ft to the unit yield and should be placed within 15-20 min.

Placement: Trowel, or screed RepCon® 928 firmly into the prepared area, ensuring intimate contact with the bonding surface. Finish RepCon® 928 level with the surrounding concrete and allow to take an initial set. After the initial set, when RepCon® 928 is surface hard, finish by hand trowelling. Excessive troweling is not required. Finishing/Curing: Finish the repair material to the desired texture to best match the surrounding concrete. Do not add additional water to the surface during finishing.


Download Helpful Information:


Packaging

RepCon® 928 is packaged in

  • 50 lb bag
  • 3,000 lb SuperSack
  • Coverage: approx 20 sq-ft @ 1/4”


The Duke Company
 can assist you with your construction needs. We offer expert advice from our highly rated customer service. Furthermore, we offer the best values and fast delivery.

         

Quote for Rock Salt & Packaged Ice Melts from the Duke Company         

           (585) 292-9870  (Rochester NY)

          (607) 347-4455  (Ithaca NY)

          (585) 335-5970 (Dansville NY)


The Duke Company ships nationwide and throughout New York, or contact us for convenient pick-up locations including:

Sign-up for the Duke Company’s Alerts

Text ‘DUKESALT’ to ’55469’ to receive text messages regarding our hours, extended hours, schedule changes and discount opportunities.

Industries we serve:

Construction

High Rises,
Bridges,
Residential & Commercial
high-rise construction, power plants,
tunnels,
mining
Building Maintenance

By David Szydlowski